(Tax Included)

Combo Included :

ALL-IN-ONE DESIGN

NAZA simplifies installation and saves space and weight. With the innovative

All-in-One design, NAZA contains inner damping, controllers, 3-axis gyroscope,

3-axis gyroscope and barometer in its light and small Main Controller. NAZA can

measure flying altitude, maintain and therefore can be used for

autopilot/automatic driving.

ADVANCED ATTITUDE STABILIZE ALGORITHM

Advanced mix guidance algorithm and control algorithm, inherits outstanding

flight stability of DJI products, provides excellent maneuverability,

gives hobbyists wonderful flight experience.

MULTILE FLIGHT CONTROL MODE / INTELLIGENT SWITCHING

Naza-M offers three types of control modes : GPS Atti. Mode(with GPS module),

Atti. Mode, Manual Mode. Customer can switch among the three modes to adjust

different flight environment even in the specially weak GPS environment. Naza-M

also can adjust automatically in the flight environment and intelligent switch between

GPS Atti.mode and Atti. Mode to make sure the safety and security of flight.

GPS MODULE AVAILABLE / ACCURATE POSITION HOLD

Naza-M GPS will greatly enhance performance for entry AP with Position Hold,

Return-To-Home and Intelligent Orientation Control. With GPS Module,

the multirotors will have position and altitude lock in windy conditions.

Precise hovering in less than 2.5m horizital and and 0.8m vertical.

INTELLIGENT ORIENTATION CONTROL

Usually, the forward direction of a flying multi-rotor is the same as the nose

direction. By using Intelligent Orientation Control (IOC), wherever the nose

points,the forward direction has nothing to do with nose direction:

In course lock flying, the forward direction is the same as a recorded nose

direction.See the following figures(Mode 2)：

In home lock flying, the forward direction is the same as the direction from

home point to multi-rotor.See the following figures (Mode 2)：

FAILSAFE MODE

If your transmitter supports Fail-Safe , then you can set Fail-Safe output of

receiver to input port-U .Naza controller has built-in auto level Fail-Safe function.

That means when the communication between MC and transmitter is disconnected,

the outputs of all command sticks from controller will go to center point . If your

transmitter has only 4 channels, then MC will work in Atti. Mode by default

without Fail-Safe function.

TWO LEVELS LOW VOLTAGE PROTECTION

In order to prevent your multi-rotor from crash or other harmful consequences

caused by low battery voltage, we have designed two levels of low voltage

protection. You can choose to not to use them, however we strongly recommend

to open the protections!

MOTOR ARM

Naza have four ways to start motor,see the following picture:

In any situation start the aircraft (include any motor disarm)Need to perform any

of the ways of breaking rod. During the flight, the motor stall, the immediate

implementation of any of the breaking lever start, the motor will now return to

the rotation, and enhance the safety of the aircraft during the flight.

MOTOR DISARM

Immediately Mode: By using this mode, in any control mode, once motors

start and throttle stick is over 10%, motors will stop immediately when

throttle stick is back under 10% again. In this case, if you push the

throttle stick over 10% in 5 seconds after motors stop, motors will re-start .

If you don’t push throttle stick after motors start in three seconds, motors

will stop automatically.

Intelligent Mode: By using this mode, different control mode has different

way of stopping motors. In Manual Mode, only executing CSC can stop motors.

In Atti Mode. any one of following four cases will stop motors:
a) You don’t push throttle stick after motors start in three seconds;
b) Executing CSC;
c) Throttle stick under 10%, and after landing 3 seconds.
d) The slope angle of multi-rotor is over 70°, and throttle stick under 10%.

SUPPORTING FUTABA S-BUS RECEIVER

Four channels and more than four-channel receiver supportted, also

PPM and S-Bus receiver supportted.
S-Bus receivers (the general use of the first 8 channels of S-Bus receiver)

to optimize the channel connection, the A, E, T, R, U five-channel function

set in a channel of X2, use only oneservo cable to the S-Bus and X2 can

makes installation quick and easy, not easy to make mistakes.

6 TYPES OF MULTI-ROTORS

NAZA support six different multi-rotor model, Meet the different

needs of the enthusiasts.

BUILT-IN GIMBAL STABILIZATION FUNCTION

The gimbal stabilization module is compatible with almost all 2-axis

gimbal systems. The system will adjust the gimbal and camera

according to the attitude of the helicopter after setting the

parameters the first time.

REMOTE ADJUSTMENT AND FIRMWARE ONLINE UPDATE

Easy firmware upgrade, extendible port for future use is available.

Hardware

Hardware Install Problems

Software Settings Problems